Lever arm shock absorbers

A company which reconditions these shock absorbers is;

Stevson Motors Ltd (Specialist classic car hydraulic component manufacturers and recoditioners of lever arm and telescopic shock absorbers)
Unit 1, 2a Harrow Road
Selly Oak, Birmingham B29 7DN
Tel: 0121 472 1702   
Email: stevsonmotors1@aol.com

Wheel Bearings

bearings

Manufacturers do not want to make replacement from other sources that easy, regularly mixing two standard bearings into one assembly, although I doubt that Bristols went this far.

Take off one complete set of bearings (2 sets of bearings per hub; the inner bearing is usually larger than the outer; both will be tapered roller bearings) and find yourself a local  machine tool service company.   Take your bearings in and they will measure them while you wait (about 5 minutes).  There are 3 grades of bearings used classed  A, B and C.  The tolerances in manufacture are, of course, extremely tight so they employ an automatic grading system – A being the best and that’s what you want.  C are the poorest and probably go into washing machines and the like.   I think the classification system may have changed possibly 1 – 3.  If the numbers on the bearings are visible you should be able to quote these to any bearing company and avoid the need to go to a machine tool service company.

Valid at time of writing in October 2016:

There are a number of good bearing suppliers eg Seager Bearings, Kings Heath, Birmingham (0121 444 5391) who will supply at trade prices.

6 cylinder Cam Followers

Six cylinder Cam followers are available from:-

Arrow Precision Ltd
12 Barleyfield Services
Hinckley Fields Industrial Estate
Hinckley
Leicestershire LE10 1YE
UK

Tel: 000 44 1455 234200

http://www.arrowprecision.com

Available on-line under Part No. CF124 @ GB£22.50 each + VAT + carriage.(for the standard version).
Also available are racing cam followers which have a special diamond coating at GB£40.00 each.

Door boot seals & draught excluder

Please find contact details of the Furflex/draught excluder supplier:-

William Marston Ltd
70 Fazeley Street
Birmingham
B5 5RD
UK

Tel: 0044 121 643 0852 or 0044 121 643 0372

email: info@williammarstonltd.co.uk
website: http://www.williammarstonltd.co.uk

The boot seals can possibly be obtained from:-

Phoenix Supplies
Unit c1a Langlands Business Park
Uffculme
Cullompton
Devon EX15 3D4
UK
Contacts: Nigel or Kaye Coles

Tel: 0044 1884 849294

email: phoenixsupplies@hotmail.com
website: http://www.phoenixclassictrim.com

or –

Woolies (I & C Woolstenholmes Ltd)
Whitley Way
Northfields Industrial Estate
Market Deeping
Peterborough
PE6 8AR
UK

Tel: 01778 347347

email@ info@woolies-trim.co.uk
website: http://www.woolies-trim.co.uk

Both of these companies carry a large range of extruded sections and just may be able to help with boot and door sections.

Pegasus parts news

COMMERCIAL NEWS

One of our members refurbishing his brakes on his 403 enquired whether Pegasus knows of a supplier of the banjo bolts that fit into the wheel cylinders and copper sealing washers to fit these bolts.

I gave him the following company:-

Stevson Motors
Unit 1, 2A Harrow Road
Selly Oak
Birmingham
B29 7DN

Contact: Derek

Tel: – 0121 472 1702

http://www.stevsonmotors.co.uk

They can supply refurbished, lever arm shock absorbers, stainless braided flexible hoses of all kinds, brake fittings and thick wall rubber tubing as used on our 2 litre vacuum wiper systems.

Derek could not help with the banjo bolts but he recommended another company. They were able to supply them and he stated they stocked other Bristol bits.

John Lawley
Spares & Technical Support Officer

Solex Carburetter refurbishment

I had all three of my carbs rebuilt last year by:

Carburetter Exchange
28f High St, Leighton Buzzard, LU7 1EA, Tel 01525 371369

http://www.carbex.demon.co.uk/

solex2

solex1
 

 

 

They did an excellent job and the cost was £250-300 for all three – not cheap but kit now like new.  They quoted 6-12 weeks for work to be done.

Mike Say

Ed.  Extract of services provided pasted below as taken from their website Oct 2013

Over the past 80 years or so there have been innumerable carburetter designs by many different manufacturers, and it would be impossible for us to compile a detailed rebuild procedure for each one. However, all carburetters tend to follow the same principles of design, enabling us to give an indication of the various processes involved.

  • Carburetters are completely stripped.
  • Components are subjected to a four part chemical cleaning process which is the only effective way to remove dirt and corrosion from the internal circuitry as well as restoring the castings to their original appearance.
  • Castings are polished to a high standard, or stove enamelled. *
  • Mating faces are re-machined to ensure flatness.
  • The throttle spindle housing is re-bushed using P.T.F.E. lined glacier type bushes and line reamed to correct tolerance.
  • Steel components are de-rusted and inhibited.
  • Steel components are re-plated. *
  • Brass components are chemically brightened.
  • Brass components are polished. *

* Denotes concours service only.

Carburetters are now re-assembled using all new wearing components, i.e.:

  • Throttle spindle
  • Float needle valve
  • Throttle plate
  • Volume/Air screw
  • Throttle plate screws
  • Diaphragms
  • Metering needle
  • Seals and washers
  • Jet Ancillaries
  • Gaskets

Any other components found to be faulty will be replaced. All internal components are adjusted and set as per manufacturer’s specification.  Carburetters are then engine tested to ensure correct functioning of the following:-

Fuel level, Idle circuit, Choke mechanism, By-pass circuit, Pull down and fast-idle operation, Progression circuit, Correct throttle operation, Main circuit, Correct response to mixture adjustment, Pump circuit.

(Upon re-fitting to vehicle, normal adjustments will be necessary)

Carburetters are given a final inspection and guaranteed for 12 months.

Head spanners

Greg Lowes head spanner

Original six cylinder head spanners are rare and now very expensive.

Greg Lowe has commissioned some high quality replica head spanners.  These are made and available for purchase.  They are made in England by a quality hand tool manufacturer from high grade tool steel to the exact dimensions of the original Bristol spanner.

If you would like to purchase such a spanner, Please contact Greg Lowe direct.  Member contact details can be accessed via the front page.

Car Audio – New world tech, old world charm

The age old question for classic car owners is whether to fit a modern audio system that pleases the ear or a period radio that pleases the eye.  Stuart Risebrow has attempted to “have his cake and eat it” by fitting a modern audio system with period looks.

v8 parts-4

 

This unit, manufactured by “Retrosound”, a USA company, was found to be perfect for the job.  You have a range of period bezels and knobs to choose from that replicate the look of classic radios such as radio mobile and Phillips.  However,  the two rotating switches are detachable, allowing bespoke placement as well.

You will see that Stuart chose to make up a plywood insert to fit the mounting whole in the dash which he then veneered himself in walnut before adding a polished lacquer finish.

The “Retrosound” radio also comes with a small auxiliary unit that is wired to the rear of the radio and located remotely.  This allows you to plug in an SD memory card, USB storage device or 3.5mm audio jack.  The SD card allows you to store 1000’s of songs which is perfect for all those 60’s hits and Glen Miller tracks!  Stuart placed my remote unit just inside the glove box.  You would hardly know it was there.

The radio itself has an inbuilt amp that provides plenty of “oomph” and has all the expected outputs for larger amps, aux players or an electric ariel.

 

 

 

2 litre engine oil

Castrol Oil

Which engine oil is recommended the straight six Bristol engines?

Dave Dale and John Lawley both place great faith in Castrol Classic XL 20/50.

John Lawley, BODA technical officer, has more recently been using another oil also developed especially for classic cars. If you go to http://www.commaoil.co.uk/productsguide you will see 3 versions: a combined winter/summer oil, a dedicated winter oil and a dedicated summer oil. I use the combined version and have been very satisfied with it.

The only reason for the change is that my current motor factor does not stock the Castrol oil only obtaining it to order. However, they stock the Comma oil so I thought I would give it a try.

Classic Car Keys

This company can supply any of the Bristol key patterns, either as a duplicate or to a code.  The code can be found on the barrel of the lock.  This does entail removing the barrel from the lock.

Wilco Direct

Unit D1/D2, Pinetrees Road, Pinetrees Business Park, Norwich, Norfolk, NR7 9BB

Website

Classic car key page at time of writing

Email address